Fibre Channel directors don't just provide lots of ports, they also offer ways to connect disparate SANs, isolate data and devices within a fabric, and configure throughput for specific applications. We look at how the big three directors match up. (This article originally ran in the February 2006 issue of "
Continue Reading This Article
Enjoy this article as well as all of our content, including E-Guides, news, tips and more.
No longer just a big box with lots of ports, the Fibre Channel (FC) director has become the cornerstone around which next-generation SANs will be built. As more organizations are faced with managing petabytes of storage, director-class switches are easing management tasks by isolating SANs within a single fabric, delivering a higher level of data protection and parceling throughput to individual ports depending on changing application demands.
Of course, some things never change: First and foremost, companies look to directors to provide rock-solid stability with high levels of availability, throughput and port count. In this vein, the passive backplanes that are used in Brocade Communications Systems Inc.'s SilkWorm 48000, Cisco Systems Inc.'s MDS 9509 and McData Corp.'s Intrepid 10000 (i10K) nearly eliminate the possibility of failures. Each of these models also supports at least 1 Tbps of internal bandwidth in a single chassis and 384 FC ports in a single rack; Brocade and Cisco offer configurations that support up to 768 FC ports in a rack. But as some vendors pack more ports into their line cards to meet growing user capacity demands, they're using port oversubscription to do so.
Port oversubscription occurs when the amount of internal switching fabric bandwidth allocated to a switch port is less than the device connection speed at that port. For example, if a port on an FC switch has a connection speed of 2 Gbps, but is unable to achieve a wire-rate of 2 Gbps, then the port is said to be oversubscribed. As a result, administrators need to plan how and under what circumstances to deploy these high port-count line cards.
With core components such as passive backplanes, concurrent microcode upgrades, purpose-built ASICs and redundant hardware components essentially equal among FC directors, vendors are finding other ways to differentiate their products. And with the growing need for higher port counts, distance replication and connecting SAN islands, vendors are adding functionality to FC directors in the following key areas:
- Line cards
- 1 Gbps, 2 Gbps, 4 Gbps and 10 Gbps FC ports
- FC port buffer credits
- Inter-switch link (ISL) aggregation and connectivity options
There are tradeoffs when maximizing port capacity and using faster FC speeds. McData's i10K supports 10 Gbps FC ports, but those ports can only be connected to other i10K directors with the same 10 Gbps FC ports because 10 Gbps FC ports are based on a different technology than those at 1 Gbps, 2 Gbps and 4 Gbps speeds.
Users of Brocade's SilkWorm 48000 will encounter similar issues. A SilkWorm 48000 fully populated with its FC4-16 line cards is the company's only 4 Gbps configuration that allows its FC directors to operate at 4 Gbps without any blocking of bandwidth. Brocade's FC4-32 line cards allow scaling up to the maximum port count on its 48000, but that configuration can only operate at a maximum of 2 Gbps without blocking.
Despite these concerns, lower per-port prices are driving the move to line cards with higher port counts. Vendors report that users should generally expect to pay a 10% to 25% premium for line cards that support a higher number of ports. And despite the potential of back-end bottlenecks using the higher FC port count cards, most users aren't at risk, say vendors, because few production environments are reaching throughput limits on their FC directors. Cisco recently checked the utilization rates in its own production environment and found that most of its FC ports were averaging only 13 MBps. This prompted Cisco to see if it could lower its own internal costs by increasing the number of ports on its blades.
To find the right balance between low and high port-count line cards, you need to identify the specific configurations and applications that require high-throughput FC ports. Applications such as backup/recovery and data replication, and FC ports dedicated to ISLs require high port throughput. By taking advantage of the port buffer credit and ISL aggregation features on the director ports, and by balancing which application or configuration uses which FC ports, there may not be a need to purchase lower port-count line cards.
The primary benefit of port buffer credits is to keep data flowing across distances. The size of the buffer credit needed on each FC port will depend on four factors:
- The amount of data going through the port
- The speed of the port
- The distance between the FC ports
- If the WAN gateway devices used provide additional buffering
For distance replication, vendors generally recommend approximately one port buffer credit for every kilometer over a 1 Gbps link. In most situations, you'll only need to devote a few FC ports for long-distance replication with the rest of the ports reserved for local connectivity. To provide as much flexibility as possible, vendors offer choices for how buffer credits can be configured and re-allocated among ports.
Jerome M. Wendt (firstname.lastname@example.org) is a storage analyst specializing in the field of open-systems storage and SANs. He has managed storage for small- and large-sized organizations in this capacity.